Characteristics and Model List of Product Selection Parameters for the MI Series of Fenghua (FH) Current Detection Alloy Resistors

FH Brand Introduction Metal Current Sensing Chip Resistor Spot Check

The Fenghua (FH) current detection alloy resistor MI series products also belong to the alloy bonding category, with high strength, toughness, ultra-thin, ultra-low resistance value and other characteristics. They are widely used in products with high requirements, such as mobile phones, wearables, headphones, and so on. The FH alloy resistance MI series mainly has four volumes: 0603080512060612. This article will provide a detailed introduction to the product features, parameters, and model list of this series.

The product characteristics of the Fenghua (FH) current detection alloy resistor MI series are as follows:

1. The maximum power can reach 1W

2. The minimum TCR is ± 50PPM/℃

3 miniaturization 0603

4. Suitable for use as resistors for current detection, such as power circuits, etc

5. Compliant with RoHS directive requirements

6. Meets halogen-free requirements

The product selection manual parameters for the MI series of Fenghua (FH) current detection alloy resistors are as follows:

The electrical parameters and product models of the MI series of Fenghua (FH) current detection alloy resistors are shown in the table below:

Product number	resistance(Ω)	size(inch)	resistance tolerance	Rated power	Temperature coefficient value(ppm/℃)
MFN1225KR050FT	0.050Ω	1225	±1%	3W	±100
MFN1225HR015FT	0.015Ω	1225	±1%	3W	±50
MFN1225KR010FT	0.010Ω	1225	±1%	3W	±100
MFL1225KR010FT	0.010Ω	1225	±1%	2W	±100
MFK0612KR010FT	0.010Ω	0612	±1%	1.5W	±100
MFJ0612HR010FT	0.010Ω	0612	±1%	1W	±50
MFK0612HR010FT	0.010Ω	0612	±1%	1.5W	±50
MFN1225KR008FT	0.008Ω	0612	±1%	3W	±100
MFK0612KR008FT	0.008Ω	0612	±1%	1.5W	±100
MFJ0612KR007FT	0.007Ω	0612	±1%	1W	±100
MFN1225KR006FT	0.006Ω	1225	±1%	3W	±100
MFK0612KR006FT	0.006Ω	0612	±1%	1.5W	±100
MFN1225KR005FT	0.005Ω	0612	±1%	3W	±100
MFL1225KR005FT	0.005Ω	1225	±1%	2W	±100
MFK0612KR005FT	0.005Ω	0612	±1%	1.5W	±100
MFK0612KR005FT	0.005Ω	0612	±1%	1.5W	±100
MFN1225KR004FT	0.004Ω	1225	±1%	3W	±100
MFN1225KR003FT	0.003Ω	1225	±1%	3W	±100
MFK0612KR003FT	0.003Ω	0612	±1%	1.5W	±100
MFJ0612KR003FT	0.003Ω	0612	±1%	1W	±100
MFJ0612KR002FT	0.002Ω	0612	±1%	1W	±100

The above is a list of product characteristics and product selection parameters for the MI series of FH current detection alloy resistors. If you need more detailed product information and product ordering, please consult our online customer service.